Auxiliary Water Pump Diagnostics

Diagnosing Poor Heater Performance Complaints

If a vehicle comes in with a complaint of poor heater performance, the issue may be the auxiliary water pump.

A car or truck comes into your shop with a complaint of poor heater performance. The driver complains that on cold mornings the heater will blow cold during the drive to work in rush hour traffic. The car is not overheating and the air is coming from the correct ducts.

Your first reaction might be to install a new thermostat and inspect the heater core for a blockage. On the test drive, the system may perform great for you. Is the customer just cold blooded?

The issue could be the auxiliary water pump. This pump is not connected to the cooling of the engine. Its primary function is to circulate warm coolant to the heater core. If too little coolant is circulated, the blower fan will pull enough heat out of the coolant and cause the heater core to get cold.

These pumps were first used on luxury and diesel vehicles in the 1990s. Most diesel engines typically do not generate a lot of heat when running or idling. Coupled with the lower engine speeds, the coolant in the heater core would lose most of its heat before it passed through to the outlet. This would frequently cause drivers to complain about insufficient heating if they drove in stop-and-go traffic or cruised at speeds with lower RPM. So, adding an auxiliary coolant pump would provide enough volume of coolant to keep the heater core warm.

“Your first reaction might be to install a new thermostat and inspect the heater core for a blockage.”

Engineers then started to use these pumps on gasoline-powered vehicles for the same purpose. This allowed vehicle designers to use larger heater cores to provide better passenger comfort.

The control of the pump as part of the automatic temperature control system keeps the cabin heated even after the driver has turned off the ignition. The system can keep the interior warm for short periods of time while the driver goes shopping or grabs a bite to eat.

These pumps will show up on more and more vehicles as engines become more efficient and generate less excess heat. Also, new technologies like hybrid drives and stop/start systems need auxiliary pumps to not only improve driver comfort, but also to keep the batteries at a constant temperature.

Modes of Operation

Note that the auxiliary pump is not running all the time. The BCM or controlling module will control and regulate the pump using information like:
• Vehicle speed;
• Engine RPM;
• Coolant temperature;
• The temperature selected on the control head;
• Blend door position;
• Fan speed; and
• Exterior and interior temperatures.

If the vehicle has key-off control, there are additional parameters that must be met to activate the pump. These include:
• Battery voltage;
• Supply voltage to blower motor;
• Recirculation flap position;
• Security module input; and
• Keyless entry fob location.

A scan tool can test the pump function in most vehicles, but it is also possible to test the system by pressing an HVAC control head button sequence listed in the service information.

Causes of Failure

The main reason why these pumps fail is age and wear of the electric motor. Like all rotating electrical devices, brushes wear and windings short. Overheating can hasten the electric pump’s failure because increased cooling system pressures can force coolant past the shaft seals. Low coolant can also cause a pump to fail because of its position, which is typically high in the system, either on the firewall or strut tower.

“The main reason why these pumps fail is age and wear of the electric motor.”

Failure Modes

A failed pump will almost never cause the vehicle to overheat. If the auxiliary coolant pump is inoperative, the customer might notice reduced heater performance at low speeds and at idle.

Your first instinct might be to replace the thermostat, the water pump or the heater core, but if the vehicle is equipped with an auxiliary coolant pump, you will need to dig a little bit deeper with your diagnostic process.

Diagnosis

The tools needed to diagnose an auxiliary coolant pump include scan tool, meter and service information, with scan tools and service information being most important for late-model vehicles. The operation of the pump is dependent on several modules and numerous sensors that are networked.

The first step in the diagnostic process is to check for codes with a scan tool. Unrelated codes for collision detection, door module operation and loss of communications incidents can cause the deactivation of the pump. This is where service information can make the difference between a quick diagnostic process and parts swapping.

Newer vehicles may vary the voltage to control pump speed. Like all electrical devices on a vehicle, the operation is a balancing act between driver comfort and minimizing electrical loads on the alternator.

The cooling circuit on some vehicles with electric pumps may be called an auxiliary cooling circuit in the service information. The coolant may travel through the transmission cooler and windshield washer fluid bottle as part of the circuit on some models.

Hybrids

Hybrids almost always have an electric water pump to cool the battery packs and inverters, and some hybrids will have a second pump for the heater core in the cabin. Hybrids or mild hybrids with stop/start systems not only have an auxiliary cooling pump, but also electric pumps for the oil and transmission fluid.

If a pump fails on some hybrids, the system will disable the hybrid drive system or put the vehicle into a limp mode. Most hybrids also have an insulated coolant reservoir or jug that may have a pump of its own to help warm up the engine faster or keep the batteries at a constant temperature.

Not every car has an auxiliary water pump, but those that do can throw a monkey wrench in your normal diagnostic logic when solving cooling system problems.

You May Also Like

Schaeffler Group USA Expands Product Portfolio

Seventy new parts have been added to the INA, LuK and Schaeffler Bearings portfolios in the first quarter of 2024.

Schaeffler Group USA Expands Product Portfolio

Schaeffler Group USA has expanded its parts offerings for vehicles in the United States and Canada, adding over 70 new parts to the INA, LuK and Schaeffler Bearings portfolios in the first quarter of 2024. These additions expand application coverage to an additional 30 million vehicles in operation, the company said.

Protect Your Hands, Save the Planet! 

Magid introduces the flagship product in its sustainable product line – the GP102 General Purpose Work Glove.

Magid flagship product -sustainable product line – the GP102 General Purpose Work Glove.
Topology and Your Scan Tool

Topology, the term used to describe the design, layout and behavior of a serial databus configuration, influences how you access modules with your scan tool.

Topology and Your Scan Tool
The Evolution of Impact Wrench Technology

The hardest-working tool in the automotive industry has seen its share of updates and evolutions.

The Evolution of Impact Wrench Technology
Unlocking Service Drive Revenue: The Critical Role of Technician Inspections

The true potential of service consulting lies in recognizing the nuanced art of quality inspections and leveraging it to drive success for both advisors and technicians.

Unlocking Service Drive Revenue: The Critical Role of Technician Inspections

Other Posts

Addressing the Technician Shortage with Innovative Training Solutions

Drawing on extensive industry experience, the team at DealerPRO Training has developed a program that exposes technicians to future career opportunities in fixed operations as well as executive positions.

DealerPRO training
Dealership GMs Need Fewer Worries; Start Here: Recon and Appraisal Integrity

How do you manage margin compression? With a focus on predictable outcomes.

Dealership GMs Need Fewer Worries; Start Here: Recon and Appraisal Integrity
Enhancing Accessory Offerings and Car Care Products in Service Centers

By expanding product offerings, identifying top-selling items and leveraging private-label products, dealerships can create value for customers, drive revenue growth and strengthen their competitive position in the automotive industry.

Enhancing Accessory Offerings and Car Care Products in Service Centers
Rislone’s DEF Crystal Clean Helps Get Customers Out of Limp Mode

New product removes damaging crystals from SCR systems and clears P20EE codes.

New Rislone DEF Crystal Clean™ Diesel DEF & SCR Emissions System Cleaner scrubs away crystal contaminants from the selective catalytic reduction (SCR) systems of diesel cars, trucks, and SUVs to cost-effectively restore power and performance.